ACER A100 SET PDF DEFAULT PASSWORD

Otherwise the computer may not prompt forВ the password at startup.ДЁ.

Optionally, set the Password on Boot feature to 'Enable'. The password field will now change to indicate that a password has been entered.7. Enter the password again when the Setup program prompts for it, and press Enter. Type in a new password at the 'Password = ' prompt, and thenВ press the Enter key.Д¦. Press the F5 or theВ F6 key to navigate to the Password section.

ACER A100 SET PDF DEFAULT HOW TO

The next section describes how to set a Supervisor Password.)ДҐ. A Supervisor PasswordВ may be thought of asВ a backup mechanism - ifВ a User Password is forgotten, the Supervisor Password will allow access to the computer. (It may be necessaryВ to set a supervisor password before setting a user password. (This 'User Password' is equivalent to what is otherwise called, in this document,В a 'BIOS Password'.) Use the arrow keys to select 'Set User Password'. Use the arrow keys to move to the Security tab.Д¤.

ACER A100 SET PDF DEFAULT WINDOWS

If Windows starts, shut down the computer and try step 1 again.ДЈ. Immediately and repeatedly tap theВ F2 key.Дў. Starting with the computer fully off, turn it on by pressing and releasing the power button. Press theВ End keyВ and then the Y key to save changes andВ exit the BIOS Setup program.ДЎ. The Password field willВ change toВ REGISTERED.Д¦. Press the spacebar, and thenВ enter a new password at the 'Password = ' prompt. Using the arrow keys or the tab key, move to the Password field, and highlight NOT REGISTERED.Д¤. Then press (F1) key' appears on the screen.Дў.В Press the F1 key. Immediately and repeatedly tap the Esc key, until the message 'Check system. If you forgetВ the BIOS password, only a Toshiba Authorized Service Provider can remove it.ДЎ. Choose a password that you can reliably recall, or make note of it in a secure location. Once a BIOS password is set, it will be necessary to enter it whenever the computer is started, restarted or reset. To set a BIOS password, start the BIOS Setup program and enterВ a new password into theВ password field, per the detailed instructions below. TheВ Toshiba HWSetup program (found in the Windows Control Panel) may also be used for setting and disabling the BIOS password. If the computer ignores the Esc key when it's powered-on, or if you see an invitation to press the F2 key to enter the BIOS Setup utility, follow the 'F2 key BIOS' procedure, below.ДЄlmost all Toshiba notebook computers will respond to either the Esc key or the F2 key when they're first powered-on. If the message 'Check System and press the F1 key' appears, then follow the 'Esc key BIOS' procedure, below. Immediately and repeatedly tap the Esc key.

First, determine which type of BIOS is used in your notebook model, as follows: There are two main varieties of BIOS used in Toshiba notebooks, each with its own unique method forВ setting andВ disablingВ a password. With Windows XP, 2000, and NT, the password prompt is for a secure logon, meaning that it's not possible to skip over the password prompt (though it is possible to leave the password prompt blank - a 'null' password). TheВ computerВ can then be used normallyВ (though possibly with some limitations). With Windows 95, 98, and ME, this password is used only to support theВ customization of the Windows environment by each user, and the password prompt may be ignored by clicking Cancel or pressing the Esc key. The Windows password prompt appears while Windows is starting. If both are set, the Supervisor password takes precedence. Although the prompts for these two passwords have the same appearance, the passwords are set and removed differently. If you forget your BIOS or Supervisor password, you will have to have the password removed by a Toshiba Authorized Service Provider. The BIOS and Supervisor passwords cannot be removed or changedВ unless you know the existing password(s). Knowing the Supervisor password makes it possible toВ change the BIOS password, without knowing it. Exactly which settings require the Supervisor password permission varies from model toВ model. The difference between them is that if the Supervisor password is set, it must be entered in order to change system settings. Once a BIOS or Supervisor password is set, the computer will only start Windows (or any other operating system) after that password is entered correctly.Д®ntering either a BIOS password or a Supervisor password permit normal use of the computer. Both the BIOS and Supervisor password prompts appear immediately after theВ computer is started or restarted, or taken out of Standby mode.

Acer a100 set pdf default